Ernie Ball Paradigm
Results 1 to 14 of 14

Thread: My mint 2008 SR Finish is bubbling up

  1. #1
    Join Date
    Aug 2008
    Posts
    13

    Unhappy My mint 2008 SR Finish is bubbling up

    Hey,

    Pulled my bought new '08 SR Burnt Apple finish out and was playing and wiping it down good and noticed the finish has bubbled or popped up on the PU side at the bridge, but is in tact. Kind of like the bridge pressing down has scooted the finish like moving furniture on carpet. It's absolutely mint and has seen very, very little playing. It has been babied and is literally perfect--except this factory flaw. I'm sick. It's been stored in climate controlled area with my other basses (which are having no problems).

    Is this is common problem EB had or am I just an unlucky sucker who got a bad one.

    I'm not sure if I should take the bridge off to see if that will "release" the pressure and allow the finish to go back down or not. Could pop it loose and make things worse.

    I sure there's no point in contacting EB since it's way out of warranty. I suppose I'm just stuck with a finish that's going to get worse....

    Any suggestions as I grasp at straws?

    Hadn't been here in a while and that constant are you a human thing is a real joy as well.

    Thanks!
    Last edited by dagrev; 10-21-2017 at 09:13 AM.
    SR 4 Black Cherry Burst (maple)
    SR5 HH Trans Red (RW)

  2. #2
    Join Date
    Mar 2010
    Location
    Alta Loma, CA
    Posts
    1,303
    a picture is worth 1000 words



  3. #3
    Join Date
    Aug 2008
    Posts
    13
    It's just about impossible to see in a pic no matter which angle I try, but this one shows the most, but that isn't saying much.

    The finish is pushed up a little all around the front edge of the bridge plate.

    My mint 2008 SR Finish is bubbling up-20171021_144755_hedgeapple-jpg
    SR 4 Black Cherry Burst (maple)
    SR5 HH Trans Red (RW)

  4. #4
    Join Date
    Jul 2005
    Location
    San Antonio, TX
    Posts
    61
    I wonder if the bridge mounting screws could be loose. I still would not expect the finish to separate from the body as it has but it looks like the bridge has moved and has caused the finish to bubble as it has.

  5. #5
    Join Date
    Aug 2008
    Posts
    13
    Quote Originally Posted by Chuck M View Post
    I wonder if the bridge mounting screws could be loose. I still would not expect the finish to separate from the body as it has but it looks like the bridge has moved and has caused the finish to bubble as it has.
    Yes it does look that way. I checked and everything was nice and tight. I did loosen the strings and the bridge just a tad to at least take some pull off.
    Thanks
    SR 4 Black Cherry Burst (maple)
    SR5 HH Trans Red (RW)

  6. #6
    Join Date
    Aug 2012
    Posts
    622
    That definitely is odd. It looks more like the finish has "stretched out" somehow. Never seen anything like that before.
    2007 Stingray 5 HS Cherry Burst / Maple fretboard / 3 Band EQ / Ceramic Pickups
    2012 Stingray 5 H Pearl Blue / Rosewood Fretboard/ 3 Band EQ/ AlNiCo Pickup
    2012 Steve Morse Signature Morse Blueburst / Rosewood FB
    2012 Luke III SSH Vintage Sunburst / Rosewood Neck

  7. #7
    Join Date
    Aug 2005
    Location
    My Place
    Posts
    1,931
    Quote Originally Posted by Holdsg View Post
    a picture is worth 1000 words
    Need no pix for me. Got exactly same situation,
    in the same spot.

    It will prolly crack open. The affected area is no
    longer adhering to the body underneath. Just bad
    "luck off the draw".

    OTOH, same effect can appear anywhere on the
    body from impact. So pressure of the bridge can
    ultimately do this. Opaque finish allows for more
    "grippy" primer under the finish than finishes of
    any degree of transparency.
    Last edited by Golem; 10-25-2017 at 08:44 PM.
    S.U.B. SL4 - SR4p FL [x2] - SR4HH FL [Moses neck]
    SL4p FL [x2] - SL4HS FL - SL4HS FL [Moses neck]
    SR5HS alnico - SR5p FL ceramic [x2] - Bongo4Hp FL

    "Too many basses is never enuf"

    Golem is NOT engaged in social networks.

  8. #8
    Join Date
    Aug 2008
    Posts
    13
    Quote Originally Posted by Golem View Post
    Need no pix for me. Got exactly same situation,
    in the same spot.

    It will prolly crack open. The affected area is no
    longer adhering to the body underneath. Just bad
    "luck off the draw".

    OTOH, same effect can appear anywhere on the
    body from impact. So pressure of the bridge can
    ultimately do this. Opaque finish allows for more
    "grippy" primer under the finish than finishes of
    any degree of transparency.
    You are either person someone on another forum knew about or you are a third person with that problem.

    What year if your bass and what's the finish? (Trying to find any commonalities other than EB.)
    Thanks
    SR 4 Black Cherry Burst (maple)
    SR5 HH Trans Red (RW)

  9. #9
    Join Date
    Aug 2005
    Location
    My Place
    Posts
    1,931
    `

    Quote Originally Posted by dagrev View Post
    You are either person someone on another forum knew
    about or you are a third person with that problem.

    What year if your bass and what's the finish? (Trying to
    find any commonalities other than EB.)
    Thanks
    All my examples are EBMM, not brand new, not ancient
    or "vintage". Two are from impact, one is at the bridge,
    same as you described.

    Other basses on hand here have a different form of
    trans finish, NOT the the thick glossy-glassy clear coat
    thaz on the EBMMs. I think the "glassy" aspect is the
    vulnerability. Thinner finishes, lacquer finishes etc may
    be fragile, in that they may crack or chip, but "wounds"
    stay very localized. The EBMM "glass coat" behaves
    more like a sheet of glass than like paint.

    I have lacquer that has blistered from being in contact
    with a faux alligator strap. It's a chemical vapor effect.
    The EBMM "glass" finish is quite immune to that. Each
    type finish has it's benefits and drawbacks.
    Last edited by Golem; 11-30-2017 at 09:21 PM.
    S.U.B. SL4 - SR4p FL [x2] - SR4HH FL [Moses neck]
    SL4p FL [x2] - SL4HS FL - SL4HS FL [Moses neck]
    SR5HS alnico - SR5p FL ceramic [x2] - Bongo4Hp FL

    "Too many basses is never enuf"

    Golem is NOT engaged in social networks.

  10. #10
    Join Date
    Aug 2008
    Posts
    13
    Talked to EB. Told them it was years out of warranty and they requested pics and serial number. Then told me it was out of warranty and my options were to take it to a local person to see if they could fix it or buy a new body from them for $700! I didn't expect a free fix, but was a little insulted by the offer to buy a new body to replace the one that clearly had a production issue. Told them I didn't want to buy another body for an already expensive instrument. Oh well.
    SR 4 Black Cherry Burst (maple)
    SR5 HH Trans Red (RW)

  11. #11
    Join Date
    Aug 2012
    Posts
    622
    I am not sure I would term something that happens 9 years after it was made to be a "production" issue. Wood is a natural product, and it can do things like this. The wood may have slowly compressed over time, and that is the are on the guitar that would be most likely to compress, and there is nothing on top of it to prevent it bubbling up.

    Have you pulled the bridge off to see if it has moved? Maybe the bushings have compressed the wood a bit. Who knows.

    I would learn to live with it, or pull the bridge and see if you can push it back down, though I suspect that would not work. You could send it out for a refinish for a fraction of that cost, or have a good tech who works with paint see if they could do something about it.
    2007 Stingray 5 HS Cherry Burst / Maple fretboard / 3 Band EQ / Ceramic Pickups
    2012 Stingray 5 H Pearl Blue / Rosewood Fretboard/ 3 Band EQ/ AlNiCo Pickup
    2012 Steve Morse Signature Morse Blueburst / Rosewood FB
    2012 Luke III SSH Vintage Sunburst / Rosewood Neck

  12. #12
    Join Date
    Aug 2008
    Posts
    13
    After my last email, EB ran this up the food chain and will now give me a big discount on a new body. Their offer seems very fair and I'm very grateful. Way to go EB!
    SR 4 Black Cherry Burst (maple)
    SR5 HH Trans Red (RW)

  13. #13
    Join Date
    Oct 2011
    Location
    Hessen Germany
    Posts
    204

    Thumbs up

    Great !!!
    1979 StingRay natural maple

  14. #14
    Join Date
    Mar 2011
    Location
    Rhode Island
    Posts
    3,665
    Quote Originally Posted by dagrev View Post
    After my last email, EB ran this up the food chain and will now give me a big discount on a new body. Their offer seems very fair and I'm very grateful. Way to go EB!
    That's fantastic!

    2015 Luke III - BFR - Blackburst
    2014 Luke - BFR - Koa
    2013 Albert Lee - BFR (Pinkbert) with Sustainiac and Gravity Storm
    2013 Luke III - emerald green sparkle with an all rosewood neck
    2012 Morse - BFR - Dark Lord
    2012 Axis - PDN - Honeyburst
    2011 Axis - BFR - Black Sugar Roasted
    2009 Axis - Pink Quilt (Oinky) with pink video game button kill switch
    2006 StingRay - 30th Anniversary fretless

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Ernie Ball Paradigm