Ready to Roar

Search:

Type: Posts; User: tbonesullivan; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds; generated 51 minute(s) ago.

  1. Replies
    12
    Views
    355

    This is true. The Floyd Rose on the axis is...

    This is true. The Floyd Rose on the axis is "decked" on the body of the guitar. The saddles themselves on a floyd rose are also not height adjustable. This means that the only way to get the right...
  2. Replies
    12
    Views
    355

    That can just be the sound of the screws getting...

    That can just be the sound of the screws getting "stuck" and then released. I think it would really be a good idea to take off the neck, and see what is in the neck pocket acting as a shim. It looks...
  3. Replies
    12
    Views
    355

    Hmm, those plastic washers, how big are they?...

    Hmm, those plastic washers, how big are they? EBMM uses washers like those under the strap buttons on their new guitars these days. I would definitely pull the neck. It IS possible that the crack...
  4. Replies
    6
    Views
    91

    Have you replaced the battery recently? There's a...

    Have you replaced the battery recently? There's a TON more bass in the Neck position, which if you have an older battery, may simply be beyond the current capacity. Are you measuring this volume...
  5. Replies
    6
    Views
    91

    Usually the 2nd and 4th settings are weaker in...

    Usually the 2nd and 4th settings are weaker in output. The "neck only" position also has a vastly different tonal profile than the bridge only and bridge + neck position.
  6. Replies
    11
    Views
    441

    Question: I would also like to note that OEM Seymour Duncan...

    I would also like to note that OEM Seymour Duncan pickups, like Dimarzios, are almost always unmarked. That the bridge pickup reads "Seymour Duncan" says to me that it's an aftermarket retail...
  7. The bound necks are a tiny bit wider I believe,...

    The bound necks are a tiny bit wider I believe, so you'd need another axis with a bound neck. Only the BFR or PDN run axis guitars will have Stainless Frets.
  8. Did you try changing the battery? Even if it...

    Did you try changing the battery? Even if it reads a full charge, that can just be a "surface charge" and once it starts running the voltage can go lower.

    Have you made any changes to your rig...
  9. For some cases this works, but good luck playing...

    For some cases this works, but good luck playing 80s thrash with .008 strings. The pick feel is totally different, and having the higher gauge strings really is an inherent part of the sound and...
  10. Sweet! What kind of lube did you use? A lot of...

    Sweet! What kind of lube did you use? A lot of people forget that trem posts need lubrication. Also a nicely cut nut with some lurbrication there helps as well.

    I also play brass instruments, an...
  11. What kind of strange noises? crackles? Pops?...

    What kind of strange noises? crackles? Pops? squeals? Weird alien noises? The type of noise usually can help pinpoint what the problem is.
  12. Replies
    7
    Views
    390

    Help: Also, bolt on necks put pressure on the wood....

    Also, bolt on necks put pressure on the wood. Wood is a bunch of cellulose with air inside, so it squishes. Until you put the neck on, there's no real telling what is going to happen. This is why...
  13. Might be more cost effective to find one in the...

    Might be more cost effective to find one in the color you want and trade / sell yours. Is it in good condition?

    A pro refinish job is not what I would consider cheap.
  14. Replies
    7
    Views
    390

    Help: The truss rod needs to be adjusted correctly, and...

    The truss rod needs to be adjusted correctly, and from what you describe, it definitely sounds like the neck has too much relief.
  15. Replies
    8
    Views
    306

    You also might want to check the grounding of the...

    You also might want to check the grounding of the guitar, and your rig as well. A lot of venues have "crap wiring" with really bad safety grounds.

    The PAF pro is a nice lower output pickup. Just...
  16. Replies
    8
    Views
    306

    Is raising/lowering the bridge pickup an option?...

    Is raising/lowering the bridge pickup an option? That can really change how a guitar sounds. Also definitely get that silent circuit working. There shouldn't be any hum if it's setup right.

    There...
  17. Thread: Question

    by tbonesullivan
    Replies
    8
    Views
    502

    I must say, that the one time I was confronted...

    I must say, that the one time I was confronted with one of those, I dang near purchased it on the spot. They are truly incredible basses. The look, the sound, everything was thought out to make it...
  18. Thread: Question

    by tbonesullivan
    Replies
    8
    Views
    502

    The C would make much more sense: Serial...

    The C would make much more sense:

    Serial # C02749
    Manufactured April 20th, 2018
    Build Code 153-83-10-13-CS-CR
    Model 30th Anniversary StingRay5
    Color Translucent Buttercream
    Neck Roasted Maple...
  19. Replies
    10
    Views
    494

    I had heard that some versions of the Axis had a...

    I had heard that some versions of the Axis had a bar that was attached from the back of the tremolo, and not intended to be removed?
  20. Of course it's going to cause hum. You need 2...

    Of course it's going to cause hum. You need 2 coils to have hum cancelling. When you take one out, you lose that, and the hum returns, unless it's designed to have a hum cancelling circuit or dummy...
  21. NICE!!!! Good to see some new options in the...

    NICE!!!! Good to see some new options in the pedalboard game. Now if only you sold those fake pedals, so I could make everyone thing I have a massive setup when it's really just a big muff into a...
  22. Replies
    3
    Views
    240

    There should be a set screw. You can see it on...

    There should be a set screw. You can see it on the side of the knob in the first picture here:

    Valentine | Guitars | Ernie Ball Music Man

    You just need to tighten that to keep the knob on. It...
  23. Replies
    8
    Views
    547

    Just curious, but where did you see these spec...

    Just curious, but where did you see these spec lists that came with basses? I've never seen one come with an EBMM bass, except maybe a PDN or Custom Run. Even then, it would depend on what the...
  24. Replies
    8
    Views
    547

    What would be the point of sending a spec list...

    What would be the point of sending a spec list like that? That's the same for every stingray made at that time, and for years before and after. That's just a general, non specific spec list.

    I...
  25. There are many companies that install the nuts...

    There are many companies that install the nuts prior to finishing, and EBMM is one of those. If you look at the Satin clearcoat on any guitar with a "plain" headstock, you'll see that the satin goes...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Ernie Ball Forums