Flat Ribbon

Search:

Type: Posts; User: beej; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Contact customerexperience@ernieball.com and let...

    Contact customerexperience@ernieball.com and let them help you out.
  2. Replies
    72
    Views
    46,400

    Amazing job, Pete- that came out perfectly. And...

    Amazing job, Pete- that came out perfectly. And yeah, what a neck!
  3. Replies
    4
    Views
    342

    Question: I'd post mine, but it's very far from stock ......

    I'd post mine, but it's very far from stock ... so wouldn't generally be useful.

    Are you looking for a wiring diagram? Or is there something specific you're looking for in a pic?
  4. Replies
    26
    Views
    1,046

    Anyone played a Mariposa? What's the neck like?

    Anyone played a Mariposa? What's the neck like?
  5. Replies
    9
    Views
    2,370

    Well hey, great! Glad that worked out.

    Well hey, great! Glad that worked out.
  6. Replies
    26
    Views
    1,046

    Nice! I saw a photo of the neon Cutlasses a while...

    Nice! I saw a photo of the neon Cutlasses a while back ... was wondering when they'd come out.

    That Mariposa is stunning.
  7. So, a few things. There's no reason the...

    So, a few things. There's no reason the electronics will need any kind of work. Pots can be cleaned if they get scratchy, etc., and that stuff is minor surgery.

    Fret wear depends on a number of...
  8. Replies
    9
    Views
    2,370

    Did you get it wired correctly? Green to ground....

    Did you get it wired correctly? Green to ground. Black/White together. Red to one side of the toggle. There shouldn't be any bleed between the pickups.

    It's possible an older pickup sounds...
  9. Replies
    18
    Views
    812

    Question: If it floats, it'll go out of tune when you bend...

    If it floats, it'll go out of tune when you bend a string. How much depends on the tension. But there's no magic there :)
  10. Replies
    12
    Views
    934

    Rewiring a pickguard (or setting up a new one) is...

    Rewiring a pickguard (or setting up a new one) is a good project to get your feet wet with soldering and some basic electronic skills. It's not that difficult, but can be tedious if you have't done...
  11. Replies
    16
    Views
    618

    That was the one for me. Those original ones look...

    That was the one for me. Those original ones look amazing.
  12. Replies
    9
    Views
    2,370

    Just solder the black & white wires together...

    Just solder the black & white wires together (that's where the coils meet). Green goes to ground, red goes to the switch.
  13. Thread: Ngd: Sabre

    by beej
    Replies
    6
    Views
    345

    Oh man- congrats! Great to hear about the...

    Oh man- congrats! Great to hear about the pickups.

    These really do it for me. I'm trying really hard not to buy one.
  14. Replies
    22
    Views
    682

    Sort of- there's a point where you'll be...

    Sort of- there's a point where you'll be reintroducing different hum. Best bet is to set the guitar/pickguard up in playing position and adjust until you find the best spot on the trimmer. Crank up...
  15. Replies
    22
    Views
    682

    Sounds promising- it will crackle a bit when it's...

    Sounds promising- it will crackle a bit when it's powered up. If it persists, it's usually a sign that the battery isn't making good contact with the terminals. So either *gently* pry them back with...
  16. Replies
    22
    Views
    682

    Also check the output jack- it connects the black...

    Also check the output jack- it connects the black wire from the battery to ground, once a cable is plugged in. But it sounds like they just disconnected the battery. Anyhow, you'll know right away if...
  17. Replies
    22
    Views
    682

    Spud- the SC picks up the same noise your pickups...

    Spud- the SC picks up the same noise your pickups would (it's just a coil without a magnet under the hood), so it doesn't matter what frequency your power runs at ;)
  18. Replies
    22
    Views
    682

    Yes yes yes Silent Circuit! There's zero...

    Yes yes yes Silent Circuit!

    There's zero downside to have it installed. (I have on in just about every guitar- I use it for coil splitting as well as quieting single coils.) Yes, it's not going to...
  19. Replies
    2
    Views
    311

    If you use the same tension strings, there's no...

    If you use the same tension strings, there's no reason you'd magically get fret buzz after a string change.

    A sign that you've used the right set would be that your bridge is level after the...
  20. Replies
    6
    Views
    1,445

    Or turn up the treble on your amp? I change my...

    Or turn up the treble on your amp? I change my amp settings depending on which guitar I'm using.
  21. Replies
    5
    Views
    432

    I can't imagine it would be that difficult to...

    I can't imagine it would be that difficult to change, however you would need the new part to do it. (Getting the replacement would be up to you- you'd have to contact Music Man directly. Worth...
  22. Replies
    5
    Views
    432

    First off, you do have the option of replacing...

    First off, you do have the option of replacing the preamp. You'd have to send the old one to MM and purchase a replacement. Just something to keep in mind.

    It's a buffer onboard, not a preamp....
  23. Replies
    21
    Views
    1,160

    Really interested to hear how these sound. The...

    Really interested to hear how these sound. The Transition set are my favourite humbuckers at the moment. Love to hear how the new ones stack up.
  24. Replies
    5
    Views
    430

    Help: You can also try reaching out to Daniel -...

    You can also try reaching out to Daniel - customerexperience@ernieball.com. Maybe the email just got lost in the shuffle.

    Good luck!
  25. Replies
    25
    Views
    1,707

    Question: I think we're done here.

    I think we're done here.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Ernie Ball Forums