• Ernie Ball
  • MusicMan
  • Sterling by MusicMan

tkarter

Well-known member
Joined
Jun 22, 2004
Messages
5,921
Location
Kansas
It sure is easier to repair a jack in the plate rather than the body when it gets screwed up. That is reason enough right there to front mount them.

tk
 

meeder2

Well-known member
Joined
Apr 10, 2007
Messages
104
Remedy: common sense 101, run an angled cable through your strap. = no issue
 

Rod Trussbroken

Moderator
Joined
Jul 25, 2002
Messages
5,212
Location
Bris Vegas. AUSTRALIA.
I have no probs with the 2EQ control plate the way it is. In fact, I rather likey :cool:

If the jack is relocated to the body what happens to the plate...leave an empty space where the jack had once been...shorten the control plate...leave the plate the same length but space out the three control knobs?

Nope, nope and nope!
 

keko

Well-known member
Joined
Jun 10, 2009
Messages
2,702
Location
Zagreb, Croatia, EU
XLR would actually be a welcome improvement, much more sturdy connection, noiseless and locking... why are they not being used? it seems so obvious!

And FWIW i have never had a problem with the front mounted jack socket.

Why not? :)

Those two could be mounted front, bottom, or even rear on the preamp cover plate:

Cable connector:

730325_LB_00_FB.EPS.jpg


Plate connector:

746657_LB_00_FB.EPS.jpg


Of course, whole world industries of musical instruments and amplification must switch to that standard in this case! :rolleyes:
 

Big Poppa

Well-known member
Joined
Feb 9, 2005
Messages
18,598
Location
Coachella & SLO, California
Hey guys think about what you want.....you want a rigid cable between your bass and your amp....would you rather the plug pull out under stress or the amp head crash to the ground....or would you prefer ripping the faceplate off the bass....In any design there must be some place where stress can be released.
 

adouglas

Well-known member
Joined
Aug 12, 2005
Messages
5,592
Location
On the tail end of the bell curve in Connecticut
Hey guys think about what you want.....you want a rigid cable between your bass and your amp....would you rather the plug pull out under stress or the amp head crash to the ground....or would you prefer ripping the faceplate off the bass....In any design there must be some place where stress can be released.

That's why I love the power connector on my Macbook Pro. It's magnetic, so if you step on the cable it just pops off... zero damage.

My last computer died because the dog trod on the cable and caused the thing to crash to the floor.

1/4" jacks are used because they've become a defacto standard over time, just like QWERTY keyboards. There are lots of things like this.

They work, so there's no real incentive to reinvent the wheel.
 

MrMusashi

Well-known member
Joined
Mar 26, 2007
Messages
2,840
Location
69 degrees north
neutrik makes a jack outlet "plate" thing, which locks the jack in place.. i wouldnt put that anywhere near my instruments for the stress relief reasons stated earlier..
210_276241.jpg


MrM
 

silverburst

Well-known member
Joined
Oct 10, 2006
Messages
1,917
Location
Long Beach, CA
How about bluetooth?

Anyhow, I like having the jack on the front. It makes it easier to set a bass in the stand without having to unplug it.

And I hate having the Jack in Dallas. He should be out on the coast.

JackwithBongo.jpg
 

Big Poppa

Well-known member
Joined
Feb 9, 2005
Messages
18,598
Location
Coachella & SLO, California
That's why I love the power connector on my Macbook Pro. It's magnetic, so if you step on the cable it just pops off... zero damage.

My last computer died because the dog trod on the cable and caused the thing to crash to the floor.

1/4" jacks are used because they've become a defacto standard over time, just like QWERTY keyboards. There are lots of things like this.

They work, so there's no real incentive to reinvent the wheel.


love it too unless your dog chews it and you discover they charge you 86 bucks for a new one
 

keko

Well-known member
Joined
Jun 10, 2009
Messages
2,702
Location
Zagreb, Croatia, EU
1/4" jacks are used because they've become a defacto standard over time, just like QWERTY keyboards. There are lots of things like this.

OK, I agree finally, the best things in the world are always the simple useful things, right? :eek:

I wont bother anymore! :rolleyes:
 
Top Bottom